|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Bulletin PD-20628 rev. A 08/04 MBRB3030CTL SCHOTTKY RECTIFIER 30 Amp Major Ratings and Characteristics Characteristics IF(AV) Rectangular waveform VRRM IFSM @ tp = 5 s sine VF TJ @ 15 Apk, TJ = 125C (per leg) range Description/Features Units A V A V This center tap Schottky rectifier has been optimized for very low forward voltage drop, with moderate leakage. The proprietary barrier technology allows for reliable operation up to 150 C junction temperature. Typical applications are in switching power supplies, converters, free-wheeling diodes, and reverse battery protection. 150 C TJ operation Center tap configuration Very low forward voltage drop High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance High frequency operation Guard ring for enhanced ruggedness and long term reliability Values 30 30 1100 0.34 - 55 to 150 C Case Styles MBRB3030CTL BASE COMMON CATHODE 2 1 2 3 ANODE COMMON ANODE CATHODE 1 2 D2PAK www.irf.com 1 MBRB3030CTL Bulletin PD-20628 rev. A 08/04 Voltage Ratings Parameters VR Max. DC Reverse Voltage (V) VRWM Max. Working Peak Reverse Voltage (V) MBRB3030CTL 30 Absolute Maximum Ratings Parameters IF(AV) Max. Average Forward Current IFSM EAS IAR * See Fig. 5 (Per Leg) (Per Device) * See Fig. 7 Values 15 30 1100 360 13 3 Units A Conditions 50% duty cycle @ TC = 121C, rectangular wave form 5s Sine or 3s Rect. pulse Following any rated load condition and with 10ms Sine or 6ms Rect. pulse rated V RRM applied TJ = 25 C, IAS = 3 Amps, L = 2.9 mH Current decaying linearly to zero in 1 sec Frequency limited by TJ max. VA = 1.5 x VR typical Max. Peak One Cycle Non-Repetitive Surge Current (Per Leg) (Per Leg) Repetitive Avalanche Current (Per Leg) Non-Repetitive Avalanche Energy A mJ A Electrical Specifications Parameters VFM Max. Forward Voltage Drop (Per Leg) * See Fig. 1 (1) Values 0.44 0.51 0.34 0.45 2 183 0.22 6.76 2840 8.0 10000 Units V V V V mA mA V m Conditions @ 15A @ 30A @ 15A @ 30A TJ = 25 C TJ = 125 C TJ = TJ max. TJ = 25 C TJ = 125 C VR = rated V R IRM Max. Reverse Leakage Current (Per Leg) * See Fig. 2 (1) VF(TO) Threshold Voltage rt CT LS Forward Slope Resistance Max. Junction Capacitance (Per Leg) Typical Series Inductance (Per Leg) pF nH V/ s VR = 5VDC (test signal range 100Khz to 1Mhz) 25C Measured lead to lead 5mm from package body dv/dt Max. Voltage Rate of Change (Rated VR) Thermal-Mechanical Specifications Parameters TJ Tstg Max. Junction Temperature Range Max. Storage Temperature Range (1) Pulse Width < 300s, Duty Cycle <2% Values -55 to 150 -55 to 150 2.0 1.0 0.50 2 (0.07) Min. Max. 6 (5) 12 (10) Units C C Conditions RthJC Max. Thermal Resistance Junction to Case (Per Leg) RthJC Max. Thermal Resistance Junction to Case (Per Package) RthCS Typical Thermal Resistance, Case to Heatsink wt T Approximate Weight Mounting Torque C/W DC operation C/W DC operation C/W Mounting surface , smooth and greased (only for TO-220) g (oz.) Kg-cm (Ibf-in) 2 www.irf.com MBRB3030CTL Bulletin PD-20628 rev. A 08/04 1000 1000 TJ = 150C 125C 10 100C 75C 1 50C 0.1 25C Instantaneous Forward Current - I F (A) 100 R everse Current - I R(mA) 100 0.01 0 5 10 15 20 25 30 R evers Voltag e - V R(V) e Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage (Per Leg) 10000 Junction Capacitance - C T (pF) 10 TJ= 150C TJ= 125C TJ= 25C TJ= 25C 1000 1 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 100 0 5 10 15 20 25 30 35 Forward Voltage Drop - VFM (V) Fig. 1 - Max. Forward Voltage Drop Characteristics (Per Leg) 10 T hermal Impedanc e Z thJC (C/ W) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage (Per Leg) Reverse Voltage - V R(V) 1 D = 0.75 D = 0.50 D = 0.33 D = 0.25 D = 0.20 PDM t 0.1 Notes: S ingle Pulse (T hermal Resistance) 0.01 0.00001 0.0001 0.001 0.01 0.1 1 t2 1. Duty fac tor D = t 1/ t 2 2. Peak T = PDM x Z thJC+ TC J 1 10 100 t 1 , Rectangular Pulse Duration (S onds) ec Fig. 4 - Max. Thermal Impedance ZthJC Characteristics (Per Leg) www.irf.com 3 MBRB3030CTL Bulletin PD-20628 rev. A 08/04 150 Allowable Case T emperature - (C) 16 Avera ge Power Loss - (Watts) D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 DC 140 DC 12 130 S quare wave (D = 0.50) 80% Rated V Rap plied 8 R Limit MS 120 110 see note (2) 4 100 0 5 10 15 20 25 30 0 0 5 10 15 20 25 30 Average F orward Current - I F(AV) (A) Average F orward Current - I F(AV) (A) Fig. 5 - Max. Allowable Case Temperature Vs. Average Forward Current (Per Leg) Non-R epetitive S urge Current - I FS (A) M 1000 Fig. 6 - Forward Power Loss Characteristics (Per Leg) At Any R ated Load Condition And With R ated V RRM Applied Following S urge 100 10 100 1000 p 10000 (microsec) S quare Wave Pulse Duration - t Fig. 7 - Max. Non-Repetitive Surge Current (Per Leg) L HIGH-S PEED S CH WIT FREE-WHEEL DIODE 40HF L40S 02 + DUT IR P460 F R = 25 ohm g Vd = 25 Volt CURRENT MONIT OR Fig. 8 - Unclamped Inductive Test Circuit (2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ; Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6); PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ VR1 = 10 V 4 www.irf.com MBRB3030CTL Bulletin PD-20628 rev. A 08/04 Outline Table 10.16 (0.40) REF. 4.69 (0.18) 4.20 (0.16) 1.32 (0.05) 6.47 (0.25) 15.49 (0.61) 1.22 (0.05) 93 6.18 (0.24) 14.73 (0.58) 2.61 (0.10) 2.32 (0.09) 8.89 (0.35) 5.28 (0.21) 4.78 (0.19) 0.55 (0.02) 0.46 (0.02) 3X BASE COMMON CATHODE 2 1.40 (0.055) REF. 0.93 (0.37) 0.69 (0.27) 1.14 (0.045) 2X MINIMUM RECOMMENDED FOOTPRINT 11.43 (0.45) 1 1 2 3 3 4.57 (0.18) ANODE COMMON ANODE CATHODE 1 2 4.32 (0.17) 2 0.61 (0.02) MAX. 5.08 (0.20) REF. 8.89 (0.35) 17.78 (0.70) 3.81 (0.15) 2.08 (0.08) 2X Conform to JEDEC outline D2Pak (SMD-220) Dimensions in millimeters and (inches) 2.54 (0.10) 2X Tape & Reel Information TRR 1.60 (0.063) 1.50 (0.059) 4.10 (0.161) 3.90 (0.153) FEED DIR ECTION 1.60 (0.063) 1.50 (0.059) DIA. 0.368 (0.0145) 0.342 (0.0135) 1.85 (0 .07 3) 1.65 (0 .06 5) 11.60 (0.457) 11.40 (0.449) 15 .42 (0.6 09) 15 .22 (0.6 01) 1.75 (0.069) 24 .30 (0 .95 7) 23 .90 (0 .94 1) TRL 10 .90 (0.429) 10 .70 (0.421) 1.25 (0.049) 16 .10 (0.634) 15 .90 (0.626) DIA. 4.72 (0.186) 4.52 (0.178) FEED DIRECTION 13.50 (0.532) 12.80 (0.504) DIA. 26.40 (1.0 39) 24.40 (0.9 61) SMD-220 Tape & Reel When ordering, indicate the part number, part orientation, and the quantity. Quantities are in multiples 60 (2 .36 2) DIA. MIN . 360 (1 4.173) DIA. MAX. of 800 pieces per reel for both TRL and TRR. Dimensions in millimeters and (inches) www.irf.com 5 MBRB3030CTL Bulletin PD-20628 rev. A 08/04 Ordering Information Table Device Code MBR 1 B 2 30 3 30 4 CT 5 L 6 TRL 7 1 2 3 4 5 6 7 - Schottky MBR Series B = D2PAK Current Rating (30 = 30A) Voltage Rating (30 = 30V) CT = Center Tap (Dual) L = Low V F none = Tube (50 pieces) TRL = Tape & Reel (Left Oriented - for D2Pak only) TRR = Tape & Reel (Right Oriented - for D2Pak only) Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 08/04 6 www.irf.com |
Price & Availability of MBRB3030CTLTRL |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |